lite-on dcc release lite-on technology corp. / optoelectronics no.90,chien 1 road, chung ho, new taipei city 23585, taiwan, r.o.c. tel: 886-2-2222-6181 fax: 886-2-2221-1948 / 886-2-2221-0660 http://www.liteon.com/opto through hole lamp product data sheetLTL17KFL5DP1 spec no.: ds20-2015-0002effective date: 02/12/2015revision: - bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4 bns-od-fc001/a4
1 / 9 part no. : ltl 1 7kfl5d p1 bns - od - fc002/a4 through hole lamp ltl 1 7kfl5d p1 through hole lamp ltl 1 7kfl5d p1 rev description by date p001 preliminary new s pecification ( rdr - 20141374 - 02 ) javy huang 1 1 / 1 9 /2014 above data for pd and customer tracking only - new specification on opnc javy huang 1 2 / 29 /2014
2 / 9 part no. : ltl 1 7kfl5d p1 bns - od - fc002/a4 through hole lamp ltl 1 7kfl5d p1 1. description through - hole leds are offered in a variety of packages such as 3mm, 4mm, 5mm, rectangular, and cylinder which are suitable for all applications requiring status indication. several intensity and viewing angle choices are available in each color for design flexibility. 1 . 1. features ? low power consumption & h igh efficiency ? lead free product & rohs compliant . ? popular t - 1 diameter . ? source color is alingap orange 605 nm . ? amber diffused l ens . ? l ed lead frame has cutting . 1.2 . applications ? communication . ? computer . ? consumer . ? home appliance . ? industrial . 2 . outline dimensions notes : 1. all dimensions are in millimeters (inches). 2. tolerance is 0.25mm (.010") unless otherwise noted. 3. protruded resin under flange is 1.0mm (.04") max. 4. lead spacing is measured where the leads emerge from the package. 5. specifications are subject to change without notice.
3 / 9 part no. : ltl 1 7kfl5d p1 bns - od - fc002/a4 through hole lamp ltl 1 7kfl5d p1 3. absolute maximum ratings at ta = 25 c parameter maximum rating unit power dissipation 75 mw peak forward current (duty cycle Q 1/10, pulse width Q 10ms) 60 ma dc forward current 30 ma operating temperature range - 30 c to + 8 5 c storage temperature range - 4 0 c to + 100c lead soldering temperature [2.0mm (.079") from body] 260c for 5 seconds max. 4. electrical / optical chara cteristics at ta=25 c parameter symbol min. typ. max. unit test condition luminous intensity iv 140 400 680 mcd if = 20ma note 1,5 viewing angle 21/2 50 deg note 2 (fig.6) peak emission wavelength p 611 nm measurement @peak (fig.1) domi nant wavelength d 600 605 613.5 nm if = 20ma , note 4 spectral line half - width ? 17 nm forward voltage vf 2.05 2. 5 v if = 20ma reverse current ir 10 0 a vr = 5v (note 6) note: 1. luminous intensity is measured with a light sensor and filt er combination that approximates the cie eye - response curve. 2. 1/2 is the off - axis angle at which the luminous intensity is half the axial luminous intensity. 3. iv classification code is marked on each packing bag. 4. the dominant wavelength, d is deri ved from the cie chromaticity diagram and represents the single wavelength which defines the color of the device. 5. iv guarantee must be included with 15% testing tolerance. 6. reverse voltage (vr) condition is applied for ir test only. the device is no t designed for reverse operation.
4 / 9 part no. : ltl 1 7kfl5d p1 bns - od - fc002/a4 through hole lamp ltl 1 7kfl5d p1 5. typical electrical / optical characteristics curves (25 c ambient temperature unless otherwise noted)
5 / 9 part no. : ltl 1 7kfl5d p1 bns - od - fc002/a4 through hole lamp ltl 1 7kfl5d p1 6. packing spec. 1000, 500, 200 or 100 pcs per packing bag 30 packing bags per inner carton t otal 30 ,000 pcs per inner carton 8 inner cartons per outer carton t otal 24 0 ,000 pcs per outer carton in every shipping lot, only the last pack will be non - full packing
6 / 9 part no. : ltl 1 7kfl5d p1 bns - od - fc002/a4 through hole lamp ltl 1 7kfl5d p1 7 . bin table specification luminous intensity unit : mcd @20ma bin co de min. max. gh 140 240 jk 240 400 lm 400 680 note: tolerance of each bin limit is 15% dominant wavelength unit : nm @20ma bin code min max h 23 600.0 603.0 h24 603.0 606.5 h25 606.5 610.0 h26 610.0 613.5 note: tolerance of each bin limit is 1nm
7 / 9 part no. : ltl 1 7kfl5d p1 bns - od - fc002/a4 through hole lamp ltl 1 7kfl5d p1 8 . cautions 8 . 1. application this led lamp is good for application of indoor and outdoor sign, also ordinary electronic equipment. 8 . 2. storage the storage ambient for the leds should not exceed 30c temperature or 70% relative hu midity. it is recommended that leds out of their original packaging are used within three months. for extended storage out of their original packaging, it is recommended that the leds be stored in a sealed container with appropriate desiccant or in desic cators with nitrogen ambient. 8 . 3. cleaning use alcohol - based cleaning solvents such as isopropyl alcohol to clean the leds if necessary. 8 . 4. lead forming & assembly during lead forming, the leads should be bent at a point at least 3mm from the base of l ed lens. do not use the base of the lead frame as a fulcrum during forming. lead forming must be done before soldering, at normal temperature. during assembly on pcb, use minimum clinch force possible to avoid excessive mechanical stress. 8 . 5. soldering when soldering, leave a minimum of 2 mm clearance from the base of the lens to the soldering point. dipping the lens into the solder must be avoided. do not apply any external stress to the lead frame during sol dering while the led is at high temperature. recommended soldering conditions: soldering iron wave soldering temperature soldering time position 350c max. 3 seconds max. (one time only) no closer than 2 mm from the base of the epoxy bulb pre - heat pre - heat time solder w ave soldering time dipping position 100c max. 60 seconds max. 260c max. 5 seconds max. no lower than 2 mm from the base of the epoxy bulb note: excessive soldering temperature and/or time might result in deformation of the led lens or catastrop hic failure of the led. ir reflow is not suitable process for through hole type led lamp product. 8 . 6. drive method an led is a current - operated device. in order to ensure intensity uniformity on multiple leds connected in parallel in an application, it i s recommended that a current limiting resistor be incorporated in the drive circuit, in series with each led as shown in circuit a below. circuit model ( a ) circuit model ( b ) (a) recommended circuit (b) the brightness of each led might appear different due to the differences in the i - v characteristics of those leds. led led
8 / 9 part no. : ltl 1 7kfl5d p1 bns - od - fc002/a4 through hole lamp ltl 1 7kfl5d p1 8 .7. esd (electrostatic discharge) static electricity or power surge will damage the led. s uggestions to prevent esd damage: ? use a conductive wrist band or anti - electrostatic glove when handling these leds ? all devices, equipment, and machinery must be properly grounded ? work tables, storage racks, etc. should be properly grounded ? use ion blower to neutralize the static charge which might have built up on surface of the leds plastic lens as a result of friction between leds during storage and handing suggested checking list : training and certification 8.7. 1 .1 . everyone working in a static - safe ar ea is esd - certified? 8.7.1. 2. training records kept and re - certification dates monitored? static - safe workstation & work areas 8.7.2.1 . static - safe workstation or work - areas have esd signs? 8.7. 2. 2. all surfaces and objects at all static - s afe workstation and within 1 ft measure less than 100v? 8.7.2. 3. all ionizer activated, positioned towards the units? 8.7.2. 4. each work surface mats grounding is good? personnel grounding 8.7.3.1 . every person (including visitors) handling esd sensitive (esds) items wear wrist strap, heel strap or conductive shoes with conductive flooring? 8.7.3.1 . if conductive footwear used, conductive flooring also present where operator stand or walk? 8.7.3.2 . garments, hairs or anything closer than 1 ft to esd items measure less than 100v*? 8.7.3.3 . every wrist strap or heel strap/conductive shoes checked daily and result recorded for all dls? 8.7.3.4 . all wrist strap or heel strap checkers calibration up to date? note: *50v for blue led. device handling 8.7.4. 1. every esds items identified by eia - 471 labels on item or packaging? 8.7.4. 2. all esds items completely inside properly closed static - shielding containers when not at static - safe workstation? 8.7.4. 3. no st atic charge generators (e.g. plastics) inside shielding containers with esds items? 8.7.4. 4. all flexible conductive and dissipative package materials inspected before reuse or recycle? others 8.7.5. 1. audit result reported to entity esd control c oordinator? 8.7.5. 2. corrective action from previous audits completed? 8.7.5. 3. are audit records complete and on file?
9 / 9 part no. : ltl 1 7kfl5d p1 bns - od - fc002/a4 through hole lamp ltl 1 7kfl5d p1 9 . reliability test classification test item test condition sample size reference standard endurance test operation life t a = under room temperature if = per datasheet maximum drive current test time= 1000hrs 22 pcs (cl=90%; ltpd= 10 %) mil - std - 750d:1026 (1995) mil - std - 883g:1005 (2006) high temperature high humidity storage ta = 60 c rh = 90 % test time= 24 0hrs 22 pcs ( cl=90%; ltpd= 10 %) mil - std - 202g:103b (2002) jeita ed - 4701:100 103 (2001) high temperature storage ta= 105 5 c test time= 1000hrs 22 pcs (cl=90%; ltpd= 10 %) mil - std - 750d:1031 (1995) mil - std - 883g:1008 (2006) jeita ed - 4701:200 201 (2001) low temperature storage ta= - 55 5 c test time= 1000hrs 22 pcs (cl=90%; ltpd= 10 %) jeita ed - 4701:200 202 (2001) environmental test temperature cycling 100 c 25 c - 40 c 25 c 30mins 5mins 30mins 5mins 3 0 cycles 22 pcs (cl=90%; ltpd= 10 %) mil - std - 750d:1051 (1995) mil - std - 883g:1010 (2006) jeita ed - 4701:100 105 (2001) jesd22 - a104c (2005) thermal shock 100 5 c - 30 c 5 c 15mins 15mins 3 0 cycles (<20 secs transfer) 22 pcs (cl=90%; ltpd=10 %) mil - std - 750d:1056 (1995) mil - std - 883g:1011 (2006) mil - std - 202g:107g (2002) jesd22 - a106b (2004) solder resistance t.sol = 260 5 c dwell time= 101 seconds 3mm from the base of the epoxy bulb 11 pcs (cl=90%; ltpd=18.9%) mil - std - 750d:2031(1995) jeita ed - 4701: 300 302 (2001) solderability t. sol = 245 5 c dwell time= 5 0.5 seconds (lead free solder, coverage R 95% of the dipped surface) 11 pcs (cl=90%; ltpd=18.9%) mil - std - 750d:2026 ( 1995) mil - std - 883g:2003 (2006) mil - std - 202g:208h (2002) ipc/eia j - std - 002 (2004) soldering iron t. sol = 350 5 c dwell time= 3.5 0.5 seconds 11 pcs (cl=90%; ltpd=18.9%) mil - std - 202g:208h (2002) jeita ed - 4701:300 302 (2001) 1 0 . others the appe arance and specifications of the product may be modified for improvement, without prior notice.
|
